Challenger 9K Drive-On Express Pad 2-Post Lift #CL10A-XP9-2-DPC-QC

Challenger CL10A-XP9-2-DPC-QC 9,000 lb Drive-On Express Pad 2-Post Lift

Repositioning conventional lift arms two or three times before a vehicle sits square costs real minutes on every car. The CL10A-XP9-2-DPC-QC skips that step entirely with a drive-on express pad.

It's rated at 9,000 lb with a drive-on express pad instead of arms — the vehicle drives straight on and is centered on the first try. Dual pendant controls let a tech at either column run the lift without walking around the vehicle. QuickCycle trims the rise and lower time down to 27 seconds up / 17 seconds down. This configuration adds a 2' column extension, standing 164" overall — plan for a 14' minimum ceiling.

Who the CL10A-XP9-2-DPC-QC Is Built For

• Express and high-volume bays — tire, brake, quick-lube, and inspection work where spotting time is the bottleneck, not the job itself.
• Vehicles within the 9,000 lb rating — cars, crossovers, and light trucks that fit the drive-on pad footprint without needing arm adapters.
• Two-tech bays where walking to a single control station wastes time — dual pendant controls let whoever's at either column run the lift.
• High-volume bays counting minutes per vehicle — QuickCycle's faster rise and lower adds up across a full day of cycles.
• Bays that can clear 164" of column height — a 14' minimum ceiling is required for this configuration; measure before you order.

What the CL10A-XP9-2-DPC-QC Is NOT Built For

Skip this configuration if your ceiling cannot clear 164", your vehicles exceed 9,000 lbs, or your work routinely requires wheels-free suspension access that a drive-on pad does not provide. When any of those are borderline, call Alamo at (817) 865-3707 before you order.

What Makes the CL10A-XP9-2-DPC-QC Different

Configuration Highlights

• Dual Pendant Controls - an operator station at each column with Directspot™ positioning.
• Dual single-point mechanical lock release - locks disengage from either side of the bay.
• Quick Cycle™ - approximately 27 s rise and 17 s lower on a 3HP power unit.
• Drive-on express pad - 24" wide platforms sitting 2.25" off the floor for first-try spotting.
• Reinforced flip-up ramps - front and rear ramps lock upright to extend usable platform length.
• Adjustable platform length - 58" / 66.5" / 75" to match short and long wheelbases.
• 48" elongated carriage - spreads load across the column for longer service life.
• Spotting block kit included - (4) 1.5" and (4) 3" rubber blocks with (2) column-mounted storage caddies.
• Column height - 164" overall, requiring a 14' minimum ceiling.

Bay Planning Numbers

The measurements that matter here: 164" column height, 138.5" overall width, 90" drive-thru clearance, and 110" inside the columns. Compare those against doors, lights, air lines, drains, and any overhead obstruction.

Electrical and Install Coordination

Published electrical for this configuration is 3HP, 208v-230v, 60Hz, 1Ph. Have a licensed electrician confirm the circuit, disconnect, and local code requirements ahead of installation day.

Full Specifications - CL10A-XP9-2-DPC-QC

Challenger Lifts Warranty - CL10A-XP9 Series

Challenger Lifts backs the CL10A-XP9 series with the following manufacturer coverage to the original owner. Alamo routes service and support after the sale.

Warranty is to the original owner and requires registration with Challenger Lifts within 30 days of installation (otherwise the period begins from the invoice date). Coverage excludes normal wear, improper installation, and unapproved parts. Warranty service is through Alamo Equipment & Service - call (817) 865-3707.