Challenger 10,000 lb Versymmetric 2-Post Lift #VLE10

Challenger 10,000 lb Versymmetric 2-Post Lift #VLE10

A lift that only spots vehicles one way forces every tech to reposition vehicles around the lift instead of lifting around the vehicle. The VLE10 is built to remove that compromise: Versymmetric® 3-stage front arms and 2-stage rear arms let the same column set lift both symmetrically and asymmetrically, so techs reach the manufacturer's recommended lift points on sedans, SUVs, and light trucks without re-spotting.

Rated at 10,000 lbs with CL10V3-style single-point lock release and a 143.875" overall height at full stroke, the VLE10 serves shops running the Versymmetric workflow that need both symmetric and asymmetric lift points from one two-post footprint.

Who the VLE10 Is Built For

• General-service shops whose daily mix spans sedans, SUVs, and light trucks — the Versymmetric arm set lets one lift spot them all symmetrically or asymmetrically instead of repositioning vehicles around a fixed spotting style.
• Shops that keep turning away three-quarter-ton pickups and work vans because a passenger-car 10K lift is the wrong tool — the VLE10 covers that gap with 2,500 lbs per arm.
• Bays where the vehicle mix changes day to day — the fixed 131.625 in. overall-width column set handles whatever rolls in, so the shop is not re-engineering the bay every cycle.
• Techs who spot vehicles asymmetrically for door access and symmetrically for balance — the 3-stage front arms reach both sets of factory lift points from the same column set.
• Shops that have verified 12 ft (standard columns) or 14 ft (extended columns) of ceiling — the two column-height options mean the lift fits the building, not the other way around.

What the VLE10 Is NOT Built For

This is not the right choice when your vehicle weights exceed 10,000 lbs, your slab or ceiling has not been verified, or your workflow needs the CL10A's adjustable column width. If you are close on any spec, compare it with Challenger 10,000 lb Versymmetric® 2-Post Lift #CL10AV3 or call Alamo.

Important sizing note: The VLE10 publishes 10,000 lbs capacity, 74.75" rise height, and 131.625" overall width. Measure the bay and confirm the exact vehicle mix before purchase.

What Makes the VLE10 Different

Versymmetric Arm Configuration

The VLE10 pairs 3-stage front arms with 2-stage rear arms so one lift handles symmetric and asymmetric spotting. That matters because arm style and spotting approach determine how quickly the bay moves from one vehicle to the next.

• Use the published capacity and arm details as the first decision filter.
• Confirm the lift points and vehicle mix your techs see most often.
• Ask Alamo to compare it against nearby models if the workflow is mixed.
• Keep the install team involved before the bay is committed.

Single-Point Lock Release

CL10V3-style single-point lock release disengages both column locks at once from one control, instead of walking each column to release separate locks — a real time-saver at the end of every service cycle.

Bay Planning Numbers

The key measurements are a 12' standard / 14' extended ceiling requirement, 131.675"-class 131.625" overall width, and 98.375" drive-through clearance. Check these against doors, lights, air lines, drains, and any overhead obstruction.

Capacity and Vehicle Mix

The 10,000 lbs rating is the hard ceiling for the lift, not a target to exceed. If you regularly service loaded work trucks or vans, call Alamo before ordering so we can confirm the safer match.

Electrical and Install Coordination

The published electrical line is 208v-230v, 60Hz, 1 Phase. Have a licensed electrician confirm the circuit and final local requirements before installation day.

Service After the Sale

Alamo installs and services the lifts we sell, so the same team that helps size the VLE10 can support the equipment after it is in the bay.

Best For

• Bays that match the published 131.625" overall width
• Vehicles within the 10,000 lbs rating
• Shops that want one lift for symmetric and asymmetric spotting
• Shops that want Alamo installation and service support

Not Ideal For

• Unverified slabs or unknown concrete condition
• Vehicles above the rated capacity
• Bays with low obstructions that have not been measured
• Shops needing the CL10A's adjustable column width instead

VLE10 vs. Challenger 10,000 lb Versymmetric® 2-Post Lift #CL10AV3 - Which Lift Is Right for Your Shop?

Both paths stay inside Alamo's catalog. Call Alamo and we will help you decide before ordering — see the published CL10AV3 page for its full specs.

Full Specifications - VLE10

Challenger Lifts Warranty - VLE10

Challenger Lifts backs the VLE10 with manufacturer warranty coverage. Alamo helps route service and support after the sale so the shop is not left chasing a distant parts desk.

Warranty service is coordinated through Alamo Equipment & Service — call (817) 865-3707 and we help get the issue moving.

Warranty terms can change. Confirm exact coverage at the time of purchase. Warranty can be void if the lift is installed improperly or not anchored per spec.