Challenger 10K Short-Rise Scissor Lift 220V #SRM10-220
SRM10-220 is not ALI/ETL certified. Challenger lists ALI certification for the standard 115V SRM10 and SRM10-MPU configurations, but not for the 230V SRM10-220. If ALI certification is required by your shop, insurer, or local authority, call Alamo at (817) 865-3707 before ordering.
| Model | SRM10-220 |
| Capacity | 10,000 lbs |
| Lift Type | Short-Rise Pad / Scissor Lift |
| Raised Height | 22" |
| Lowered Height | 4.25" |
| Overall Length | 92.875" |
| Overall Width | 87.5" |
| Motor / Electrical | 1 HP, 230V, 50/60Hz, 1 Phase |
| Lock Positions | 13.75" / 18.25" / 21.25" |
| Surface / Flush Mount | Yes |
| ALI / ETL Certified | No |
- Minimum 4" reinforced concrete
- Minimum 3,500 PSI
- Concrete must be cured at least 28 days
- Floor should be level within 3/8" across installation area
- Keep anchors at least 8" from cracks, edges or expansion joints
- SRM10-220 uses the optional 230V configuration
- Single-phase, 50/60Hz
- Have a licensed electrician confirm circuit requirements
- Do not assume the standard SRM10 115V circuit requirements apply
- 22" maximum surface-mount rise
- Vehicle moves rearward approximately 13.25" while lifting
- Calculate overhead clearance using raised lift height plus vehicle height
- Indoor installation only
Challenger SRM10-220 10,000 lb Short-Rise Lift
The Challenger SRM10-220 combines the SRM10's compact 10,000 lb short-rise platform with Challenger's optional 230V single-phase power configuration. The lift is designed for brake, tire and quick-service work where technicians need wheel access without the height or footprint of a full-rise lift.
Surface-mounted, the SRM10 reaches 22" while lowering to just 4.25". Three mechanical lock positions allow the working height to be matched to the job, and two-position spotting blocks are included for reaching vehicle pickup points.
Who the SRM10-220 Is Built For
- Quick-service bays performing brake and tire work
- Shops that already have the appropriate 230V single-phase electrical service
- Passenger cars, SUVs and light trucks within the 10,000 lb rating
- Facilities that want surface-mount or flush-mount installation flexibility
- Bays where a full-height two-post or scissor lift is unnecessary for the work being performed
What the SRM10-220 Is NOT Built For
- Facilities that specifically require an ALI-certified lift
- Full-height underbody service requiring standing clearance beneath the vehicle
- Vehicles exceeding the 10,000 lb rated capacity
- Outdoor installation
What Makes the SRM10-220 Different
230V Power Configuration
The SRM10-220 uses Challenger's optional 230V single-phase power-unit configuration instead of the standard SRM10's 115V electrical setup.
10,000 lb Capacity in a Short-Rise Format
The lift supports vehicles up to 10,000 lbs while keeping its maximum surface-mount rise to 22", making it well suited to brake and tire service.
Three Mechanical Lock Positions
Locking heights are approximately 13.75", 18.25" and 21.25", allowing the technician to select a working position appropriate for the service being performed.
Surface or Flush Mount
Challenger supports both surface-mounted and flush-mounted installations. A flush installation reduces the lowered platform height to floor level but requires a properly constructed pit.
Two-Position Spotting Blocks
Standard two-position adapters provide approximately 4.75" and 6.75" pickup heights for reaching vehicle lift points.
Full Specifications - SRM10-220
| Model | SRM10-220 |
| Lifting Capacity | 10,000 lbs |
| Surface-Mount Raised Height | 22" |
| Surface-Mount Lowered Height | 4.25" |
| Surface-Mount Lock Heights | 13.75" / 18.25" / 21.25" |
| Low Adapter Position | 4.75" |
| High Adapter Position | 6.75" |
| Overall Width | 87.5" |
| Outside Width of Platforms | 72" |
| Width Between Platforms | 23" |
| Platform Length | 50" |
| Ramp + Platform Length | 82.5" |
| Overall Length | 92.875" |
| Rearward Movement | 13.25" |
| Motor | 1 HP |
| Electrical | 230V, 50/60Hz, 1 Phase |
| Hydraulic Pressure at Capacity | 1,720 PSI |
| Hydraulic Fluid | 6 quarts 10W anti-foam / anti-rust hydraulic oil or Dexron III ATF |
| Installation | Surface Mount or Flush Mount |
| Indoor Use | Yes - outdoor installation prohibited |
| ALI / ETL Certified | No |
| Color | Black |
⚠️ Installation Requirements
- Concrete: Minimum 4" steel-reinforced, 3,500 PSI concrete cured at least 28 days.
- Electrical: SRM10-220 uses the optional 230V single-phase power unit. Have a licensed electrician confirm circuit sizing.
- Anchoring: Follow Challenger's anchor placement and torque specifications in the current installation manual.
- Hydraulic fluid: Challenger specifies 6 quarts of approved hydraulic oil or Dexron III ATF.
- Location: Indoor installation only.
- Installation: Installation available via quote. Call (817) 865-3707.
Challenger Warranty - SRM10 Series
Current Challenger warranty documentation for the SRM10 series provides the following coverage terms to the original owner, subject to Challenger's registration, installation, maintenance and warranty conditions.
| Coverage | Term |
|---|---|
| Structural Parts | 1 Year |
| Functional Parts | 1 Year |
| Labor | 1 Year |
| Wear Items / Accessories | 90 Days |
Warranty registration should be completed with Challenger after installation. Current manufacturer terms and exclusions apply.
❓ Frequently Asked Questions - SRM10-220
Is the SRM10-220 ALI certified?
No. Challenger's 230V SRM10-220 configuration is not listed as ALI/ETL certified. The standard 115V SRM10 and SRM10-MPU are the certified configurations.
Is SRM10-220 actually 220V or 230V?
The configuration is sold under model SRM10-220, while Challenger's current technical documentation identifies the optional motor as 230V single phase. Use the equipment nameplate and current wiring documentation for final electrical installation.
Can the SRM10-220 be installed flush with the floor?
Yes. Challenger supports both surface-mount and flush-mount SRM10 installations. Flush mounting requires a properly constructed pit according to the installation manual.
What concrete does the SRM10 require?
Challenger specifies at least 4" of steel-reinforced 3,500 PSI concrete cured for at least 28 days and in good condition.
Why Buy the SRM10-220 from Alamo Equipment & Service?
- Installation available. Call for an installation quote and site review.
- We help verify electrical requirements. The SRM10-220 uses a different power configuration from the standard 115V SRM10.
- We help verify certification needs. We can compare this model with the ALI-certified SRM10 if certification matters for your facility.
- Service support. Call Alamo after the sale for lift service and parts assistance.
Call (817) 865-3707.
Shipping follows the method shown on the product page and at checkout. Standard parcel, calculated LTL, freight quotes, included freight, and pickup may apply by item.