Challenger 10K Versymmetric® 2-Post Lift #CL10AV3-QC-EV

Challenger CL10AV3-QC-EV 10,000 lb Versymmetric® 2-Post Lift

Running cars and trucks through the same bay usually means picking a lift geometry that favors one vehicle type over the other. The CL10AV3-QC-EV is built to stop that trade-off.

The CL10AV3-QC-EV runs on Challenger's Versymmetric® platform, with directSPOT™ 3-stage front and rear arms so the same lift reaches factory lift points on a sedan one cycle and a full-size pickup the next, without an arm or adapter swap in between. It runs Challenger's standard single-point control layout — simpler to operate, and typically a lower price than a dual-pendant configuration. QuickCycle™ trims real seconds off every rise and lower cycle. The EV Kit adds low-profile, EV-ready foot pads and an adapter set, so you're not improvising battery-pack clearance on the EVs and hybrids that roll in.

Columns stand 11' 2" / 11' 8" tall on this configuration — plan for a 12' ceiling minimum and measure to your lowest overhead obstruction, not the ceiling peak, before you order.

Who the CL10AV3-QC-EV Is Built For

• Shops with a 12' ceiling that keep running into column-height limits — the CL10AV3-QC-EV's 11' 2" / 11' 8" columns give you the overhead clearance a standard-column 10K model can't, without forcing a jump to a 12K or 15K lift you don't need for the capacity.
• Bays that see both passenger cars and trucks in the same shift — Versymmetric® arm geometry spots symmetrically for trucks and vans and asymmetrically for cars, so the tech doesn't reconfigure anything switching between a sedan and a pickup.
• Single-operator shops that don't need dual-station controls — one control point keeps the lift simpler to operate and typically lowers the price versus a DPC configuration, without giving up capacity or arm reach.
• High-volume bays counting minutes per vehicle — QuickCycle™'s faster rise and lower adds up across a full day of 15-20+ vehicle cycles in a way a standard-speed lift can't match.
• Shops already seeing EVs and hybrids on the schedule — the included EV Kit's low-profile foot pads and adapters mean you're not scrambling for a battery-pack-safe lift point adapter mid-job.
• Buyers who want one team for sizing, delivery, install, and service — Alamo measures your bay, installs the lift, and stays the call for warranty and service afterward instead of handing you off to a separate installer.

What the CL10AV3-QC-EV Is NOT Built For

This is not the right choice when your ceiling can't clear the 11' 2" or 11' 8" columns, your vehicles exceed 10,000 lbs, or your slab hasn't been verified. If you're close on any spec, call Alamo at (817) 865-3707.

What Makes the CL10AV3-QC-EV Different

Configuration Highlights

• Versymmetric® directSPOT™ arms - 3-stage front and rear, lift symmetrically or asymmetrically in one bay.
• Controls: Conventional single-point power controls.
• Column height: standard 11' 2" or 11' 8" columns for 12' shop ceilings.
• QuickCycle™: faster 27-second rise and 17-second lower to boost bay throughput.
• Includes the Challenger EV Kit: 4× EVFPK low-profile EV-ready foot pads, 4× universal foot pads, 4× 3-inch adapters, 4× 6-inch adapters, and 4× storage rack

Bay Planning Numbers

The measurements that matter: 11' 2" or 11' 8" column height, 11' 6½" overall width, and 100" drive-through clearance. Check these against doors, lights, air lines, drains, and any overhead obstruction.

Electrical and Install Coordination

The published electrical line is 208-230V, 60Hz, 1Ph, 20A. Have a licensed electrician confirm the circuit and final local requirements before installation day.

Full Specifications - CL10AV3-QC-EV

Challenger Lifts Warranty - CL10 Series

Challenger Lifts backs the CL10AV3 series with the following manufacturer coverage to the original owner. Alamo routes service and support after the sale.

Warranty is to the original owner and requires registration with Challenger Lifts within 30 days of installation (otherwise the period begins from the invoice date). Coverage excludes normal wear, improper installation, and unapproved parts. Warranty service is through Alamo Equipment & Service - call (817) 865-3707.