Stratus Extra Wide 12k lbs Single Point Manual Release 2-Post Lift #SAE-F12X

Stratus SAE-F12X — 12,000 lbs 2-Post Lift

Your bay has a low ceiling, your budget has a ceiling too, and the two keep colliding. The 12,000 lb lifts you can actually afford are tall overhead units that won't fit under your trusses, and the low-profile options either cost more than the job justifies or top out at a capacity that leaves your heavier trucks on the ground. You're stuck choosing between equipment that doesn't fit and equipment that doesn't pencil out.

The Stratus SAE-F12X breaks that deadlock — a value-priced 12,000 lb two-post lift built low and wide. Its baseplate design runs the equalization cables across the floor instead of overhead, dropping the overall height to just 122 1/2" so it tucks into bays an overhead 12k lift can't enter. The extra-wide column spread gives wider trucks and vans a clean path between the posts, with 129 15/16" inside the columns and a 116 3/16" drive-thru. A 4 HP 220V 30A motor runs it, single-point manual lock release drops all the locks from one handle, and the only thing you trade for the low height and the lower price is a cable channel across the floor — a fair swap when the alternative is no lift that fits at all.

Who the SAE-F12X Is Built For

• You're opening or expanding on a tight budget and need real 12,000 lb capacity without paying a premium for an overhead design your low ceiling can't even use. The F12X is built to be the value pick that still fits.
• Your building has low clearance — an older garage, a converted bay, a unit with overhead obstructions — and the 122 1/2" overall height is the difference between installing a 12k lift and giving up on one.
• You service wider trucks and vans that scrape past standard-width lifts, and the extra-wide column spread with a 116 3/16" drive-thru finally gives those vehicles room to drive straight in.
• You're a side-business or part-time shop that needs a dependable heavy lift but can't justify top-tier pricing. A baseplate 12k at this price point earns its keep without overspending.
• You already run an air-and-fluid setup along the floor and a cable channel doesn't bother you — you'd rather put your money into capacity and column width than into clearing the floor.
• You're comparing the Atlas BP-12000 and want the same low-ceiling baseplate 12k, but bought through someone who'll verify it fits your bay and stand behind it instead of just listing the price.

What the SAE-F12X Is NOT Built For

• ❌ Shops that want a fully clear floor (baseplate runs across the floor)
• ❌ Light-duty car-only shops where a 10,000 lb lift is more economical

What Makes the SAE-F12X Different

Low-Ceiling Baseplate Design

The SAE-F12X runs its equalization cables across a floor-level baseplate rather than an overhead crossbar, which pulls the overall height down to just 122 1/2". That low profile is the whole reason the lift exists: it tucks into older garages, converted bays, and units with overhead obstructions that a tall overhead 12k lift can't enter. For a shop boxed in by clearance, the baseplate isn't a downgrade — it's the difference between installing a real 12,000 lb lift and giving up on one because the ceiling said no.

Capacity & Lift Height

The SAE-F12X delivers a full 12,000 lb capacity at a value price, so you cover half-ton pickups through 3/4-ton work trucks without paying a premium for an overhead design your low ceiling can't use. You no longer choose between the capacity your heavier rigs need and the budget the job justifies — the F12X gives you genuine heavy-lift capability in an affordable low-profile package, keeping your money in equipment rather than in clearing a roof you don't have.

Bay Fit & Clearance

With 129 15/16" inside the columns and an extra-wide 116 3/16" drive-thru, the SAE-F12X lets wider trucks and vans drive straight in between the posts instead of scraping past a standard-width lift. Combined with the 122 1/2" overall height, it solves both the width and the height of a tight bay at once. Alamo checks those clearance numbers against your real building and your widest rigs before the lift ships, so it fits the first time instead of becoming an expensive freight return.

Included Adapters

Every SAE-F12X arrives complete with four adjustable rubber lift pads and four truck adapters in the crate — not a hidden parts order that surfaces after delivery and stalls your first job. The adjustable pads set clean contact at factory pickup points across cars and light trucks, while the truck adapters add reach for the taller frames on heavier pickups and vans. Because the right hardware ships with the lift, the value buy stays a value buy — no surprise add-ons before you can raise a vehicle.

Power & Hydraulics

The SAE-F12X runs on a 4 HP, 220V single-phase motor with a 30-amp breaker — the same electrical class as a shop welder or rotary-screw compressor, so most existing shops need only a line run to the lift instead of a panel upgrade. The hydraulic system uses standard AW32 or AW46 oil you likely already keep on the shelf. Common power and common oil hold the install cost down, which keeps a value-priced 12k lift genuinely affordable instead of quietly tacking an electrician's bill onto the purchase.

Full Specifications — SAE-F12X

Stratus Warranty — SAE-F12X

Stratus backs the SAE-F12X with comprehensive coverage. Every component is covered from the day it ships.

Warranty service is through Alamo Equipment & Service. When you buy from us, you are not waiting on a manufacturer hotline — call (844) 480-6059 and we handle it. Verify the model-specific warranty terms on the Stratus spec sheet at purchase.