Tuxedo 10,000 lb Two Post Clear Floor --Direct Drive - Bi #TP10KAC-DX

Tuxedo TP10KAC-DX — 10,000 lb ALI-Certified Two Post Lift

The Tuxedo TP10KAC-DX is a 10,000 lb capacity two-post clear-floor lift built and ALI-certified for general automotive and light-truck service. Bi-symmetric front and rear arms with a short-arm reach of 23 in–45 in and long-arm reach of 41 in–59 in are designed to center a wide range of vehicle wheelbases and configurations under the lift's rated per-arm capacity of 2,500 lb.

It uses a direct-drive hydraulic cylinder system with single-piece columns, rubber door guards to protect vehicle doors during arm swing, and a single-point manual lock release for quick, even lowering. Overall height is 144 in with a max lift height of 71 in, on a 116 in width between columns and 104 in of drive-thru clearance — a clear-floor design with no obstruction between the columns at ground level.

It's built for general repair shops, tire and quick-service centers, and any facility that needs a certified, code-compliant two-post lift rated for full-size trucks and SUVs up to 10,000 lb, backed by ALI (Automotive Lift Institute) certification for insurance and inspection purposes.

Who It's Built For

• ✅ General repair shops and dealerships needing ALI-certified lift documentation for insurance, inspection, or franchise requirements
• ✅ Facilities servicing full-size trucks, SUVs, and passenger vehicles up to 10,000 lb
• ✅ Shops that want a clear-floor design with no floor plate obstruction for tools, jacks, and creepers

What It's NOT Built For

• ❌ Vehicles or loads exceeding 10,000 lb total or 2,500 lb per arm
• ❌ Shops without adequate slab thickness/condition to meet ALI anchoring requirements — verify before ordering

Questions about fit, freight, or capacity? Call Alamo at (817) 865-3707.

What Makes the TP10KAC-DX Different

ALI Certification

The TP10KAC-DX carries ALI (Automotive Lift Institute) certification, giving shops documented third-party validation of the lift's design and load ratings for insurance, OSHA, and inspection purposes.

Bi-Symmetric Arm Configuration with 2,500 lb Per-Arm Capacity

Bi-symmetric arms (short arm: 23 in–45 in reach; long arm: 41 in–59 in reach) are designed to center a wide range of vehicles under the lift, each arm rated to 2,500 lb.

Direct-Drive Hydraulics, Single-Piece Column

A direct-drive push-cylinder hydraulic system and single-piece column construction simplify the lifting mechanism and reduce alignment points versus a cable-drive design.

Clear-Floor Design

No floor plate between the columns, keeping the bay floor open for jacks, tool carts, and creepers during service.

Footprint

116 in between columns, 145-1/2 in overall width with power unit, and 104 in drive-thru clearance — confirm against your bay before ordering.

✅ Best For

• ✅ Shops needing ALI-certified documentation for insurance or franchise compliance
• ✅ General service bays lifting full-size trucks and SUVs up to 10,000 lb
• ✅ Facilities that want a clear floor between columns for tool and jack access

❌ Not Ideal For

• ❌ Loads over 10,000 lb total or 2,500 lb per arm — see the TP11KC-DX or TP12KSC-DX for higher capacity
• ❌ Bays with insufficient slab thickness for proper column anchoring

TP10KAC-DX vs. TP11KC-DX vs. TP12KSC-DX — Which Two-Post Lift Capacity Fits Your Bay?

All three are direct-drive two-post clear-floor lifts from the same Tuxedo two-post line, differing mainly in capacity and per-arm rating.

Choose the TP10KAC-DX for ALI-certified 10,000 lb general service; step up to the TP11KC-DX for 11,000 lb capacity or the TP12KSC-DX for 12,000 lb ALI-certified heavy-duty work. Call (817) 865-3707 to confirm the right fit for your vehicles.

Full Specifications — TP10KAC-DX

Warranty — TP10KAC-DX

For exact warranty terms and coverage on the TP10KAC-DX, please contact Alamo Equipment at (817) 865-3707.